52,28€- The ducts will fit to to Mocal, A.P.S or Racetech oil coolers with a 235mm wide matrix
- Available to suit 3 different oil cooler sizes
- Fitting kit includes: 1 x cooler duct, 4 x pull through ties, 8 x rubber washers, 4 x locking tabs
879,99€Our unique DSG Oil Cooler Kit is major improvement to any 6-speed DSG (DQ250) car that’s used hard. It’s a complete ready to install package, using a clever sandwich plate design for straightforward and completely reliable installation.
922,00€Racingline DSG Oil Cooler System for MQB DQ381 (7 Speed Only) – VWR29DQ381
It’s not just your engine oil that you need to protect. Your DSG gearbox is susceptible to overheating. And the higher your power, the harder you drive, the more important it is to protect it.
Under hard driving, the factory DSG oil/water cooler is easily overwhelmed. Problems start to occur when oil cannot dissipate its collected heat fast enough and the oil begins to thin and degrade – losing its lubrication properties.
- When this happens, the DSG will protect itself and begin to lower the torque, increase shift times and in extreme circumstances even loose gear selection.
- The RacingLine kit solves this problem: by adding in an additional air/oil cooler positioned right in the airflow at the front of the car, oil temperatures are reduced by around 15 – 20 degrees centigrade (of course dependant on how the car is being used, ambient temps and state of tune).
- The kit uses a clever design which retains the factory oil/water cooling and adds to it with the thermostatically-controlled front-mounted cooler – doubling up your cooling capability when it’s needed with less heat transfer into the water system.
- Only when the oil exceeds normal temperatures, the thermostat opens. Oil temperature then drops significantly as it is pumped through the densely packed fins of the 10-row cooler’s large surface area mounted right in the cool airflow.
748,23€- For Toyota Yaris GR (2020+)
- Engine code: G16E-GTS
- Ideal for intensive use
- 10°C+ of oil temperature reduction
- Built-in thermostat (opening between 73 and 84°C)
- Comes complete with all accessories required for installation: hoses, bolts, brackets, fittings, etc.
- GReddy part number: 12014640
- Made in Japan
820,42€ – 864,95€Some aggressive track laps can overheat your oil and wear out your engine, so Mishimoto’s engineers have developed an oil cooling solution for your Focus 3 RS! The Mishimoto engineers designed the heat exchanger for this project from scratch to create the one of largest oil cooler they offers and mounted it in the front of the vehicle where it receives the most airflow. Application-specific braided stainless steel lines transfer the oil from the cooler to the engine and feature -10AN fittings for an easy installation. This 2016 Focus RS oil cooler kit is available with either a Sleek Silver or Stealth Black cooler as well as an optional thermostatic sandwich plate.
- Select your color
- Select with or without thermostat sandwich plate
600,63€Our Oil Cooler Kit is an essential fit for any hard-driven Golf 7 2.0 TSI EA888.3 engine running high power levels or in extreme climates. Increased oil temperatures means only one thing: a decrease in the ability for your engine to stay properly lubricated.
71,75€ – 325,94€7 Row – 50x210x52 mm
10 Row – 50x210x76 mm
13 Row – 50x210x99 mm
16 Row – 50x210x122 mm
19 Row – 50x210x146 mm
25 Row – 50x210x193 mm
50 Row – 50x210x389 mm
86,09€ – 365,91€7 Row – 50x330x52 mm
10 Row – 50x330x76 mm
13 Row – 50x330x99 mm
16 Row – 50x330x122 mm
19 Row – 50x330x146 mm
25 Row – 50x330x193 mm
34 Row – 50x330x264 mm
40 Row – 50x330x310 mm
44 Row – 50x330x342 mm
50 Row – 50x330x389 mm
114,80€ – 318,77€10 Row – 50x405x76 mm
13 Row – 50x405x99 mm
15 Row – 50x405x115 mm
19 Row – 50x405x146 mm
25 Row – 50x405x193 mm
34 Row – 50x405x264 mm
98,72€Designed to keep your high-performance and race vehicle oil temperatures low to prevent damage or even seizure of the engine. obp Motorsport’s Universal Oil Coolers will extend the life of your engine by ensuring your engine components are supplied with cooler oil.
Product Information:
Rows: 10 Row
Matrix: 285mm
Inlet: M22x1.5 Female
Outlet: M22x1.5 Female
Pressure Tested: 0.8MPa – 116psi
- 1
- 2
Product Categories
- Car Care & Detailing
- Gaming Simulators
- Motorsport
- Performance
- Brake System
- Car Exterior
- Cooling System
- Electronic Equipament
- Engine
- Bolts and Studs
- Camshaft kits & pulleys belts
- Dress Up
- ECU
- Engine Bearing
- Engine Gasket
- Engine Mounts
- Fuel System
- Gaskets & Seals
- Ignition System
- Intercooler & Chargecooler
- OEM & Replacement Parts
- Oil pump
- Oil Systems
- Pistons And Rods
- Service Items
- Service Kits
- Silicone Pipes & Accessories
- Thermal Protections
- Valves & Springs
- Exhaust Systems
- Gearbox
- Intake & Air Filters
- Interior
- Oils & Fluids
- Suspension & Steering
- Turbos & Superchargers Kits
- Racing Lifestyle
- Super Deals
- Wheels & Tyres